Printer error messages

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Ok, I have an HP pcs1315v all in one printer, connected by usb.  It is
detected and installed just fine.  I normally keep it off, until ready
to use it.

Well, when I turn it on, and go to print something, as in this email,
then I see the printer icon and says it is, but in turn most of the time
it doesn't.  And below is a message I see from /var/log/messages when it
errorred, to include the time it was turned on, to the error message
itself..

Jan  5 17:46:12 scrappy kernel: usb 3-2: new full speed USB device using
ohci_hcd and address 2
Jan  5 17:46:13 scrappy kernel: usb 3-2: configuration #1 chosen from 1
choice
Jan  5 17:46:13 scrappy kernel: usblp0: USB Bidirectional printer dev 2
if 1 alt 0 proto 2 vid 0x03F0 pid 0x3F11
Jan  5 17:46:13 scrappy kernel: usbcore: registered new interface driver
usblp

Jan  5 17:46:16 scrappy python: hp-probe[2243]: warning: No devices
found on the 'usb' bus. If this isn't the result you are expecting,
Jan  5 17:46:16 scrappy python: hp-probe[2243]: warning: check to make
sure your devices are properly connected and powered on.
Jan  5 17:46:17 scrappy python: hp-probe[2245]: warning: No devices
found on the 'usb' bus. If this isn't the result you are expecting,
Jan  5 17:46:17 scrappy python: hp-probe[2245]: warning: check to make
sure your devices are properly connected and powered on.

Jan  5 17:47:45 scrappy psc_1310_series?serial=CN491B619BO2:
io/hpmud/musb.c 549: invalid product id string: Operation not permitted
Jan  5 17:47:45 scrappy psc_1310_series?serial=CN491B619BO2:
io/hpmud/musb.c 1003: unable to open
hp:/usb/psc_1310_series?serial=CN491B619BO2
Jan  5 17:47:45 scrappy psc_1310_series?serial=CN491B619BO2: INFO: open
device failed; will retry in 30 seconds...
Jan  5 17:47:46 scrappy hpijs: io/hpmud/musb.c 549: invalid product id
string: Operation not permitted
Jan  5 17:47:46 scrappy hpijs: io/hpmud/musb.c 1003: unable to open
hp:/usb/psc_1310_series?serial=CN491B619BO2
Jan  5 17:47:46 scrappy kernel: CPU0: Temperature above threshold, cpu
clock throttled (total events = 2491)
Jan  5 17:48:15 scrappy psc_1310_series?serial=CN491B619BO2:
io/hpmud/musb.c 549: invalid product id string: Operation not permitted
Jan  5 17:48:15 scrappy psc_1310_series?serial=CN491B619BO2:
io/hpmud/musb.c 1003: unable to open
hp:/usb/psc_1310_series?serial=CN491B619BO2
Jan  5 17:48:15 scrappy psc_1310_series?serial=CN491B619BO2: INFO: open
device failed; will retry in 30 seconds...

After a reboot, it starts up and prints just fine.

Any ideas?  Tim W?

-- 
Mike Chambers
Madisonville, KY

"The best lil town on Earth!"


[Index of Archives]     [Current Fedora Users]     [Fedora Desktop]     [Fedora SELinux]     [Yosemite News]     [Yosemite Photos]     [KDE Users]     [Fedora Tools]     [Fedora Docs]

  Powered by Linux