Le mardi 01 fÃvrier 2005 Ã 22:56 +0100, Eric Tanguy a Ãcrit : > > On Tue, 01 Feb 2005 19:52:31 +0100, Eric Tanguy > > <eric.tanguy@xxxxxxxxxxxxxx> wrote: > > > Le mardi 01 fÃvrier 2005 Ã 13:11 +0000, Simon Andrews a Ãcrit : > > > > Eric Tanguy wrote: > > > > > Le dimanche 30 janvier 2005 Ã 20:18 +0100, Eric Tanguy a Ãcrit : > > > > > > > > > >>My bt878 capture card worked before but now with the last updated kernel > > > > >>i can't have it to work. I have no /dev/video*. What could be the > > > > >>problem ? > > > > >> > > > > >>Thanks > > > > >>Eric > > > > > > > > > > When i launch sudo modprobe bttv > > > > > FATAL: Error inserting bttv > > > > > (/lib/modules/2.6.10-1.741_FC3/kernel/drivers/media/video/bttv.ko): > > > > > Unknown symbol in module, or unknown parameter (see dmesg) > > > > > > > > > > And in dmesg : > > > > > bttv: Unknown parameter `' > > > > > > > > This sounds familiar - others have reported the same message for > > > > different modules. I belive that the new kernel is more picky about the > > > > formatting of modprobe.conf. Specifically it barfs if there are extra > > > > spaces at the end of any of the lines. Try deleting any trailing spaces > > > > on lines in modprobe.conf and trying again. > > > > > > > > Simon. > > > > > > > Now the problem is that i receive nothing using tvtime. > > > I have this in demsg : > > > Linux video capture interface: v1.00 > > > bttv: driver version 0.9.15 loaded > > > bttv: using 8 buffers with 2080k (520 pages) each for capture > > > bttv: Bt8xx card found (0). > > > ACPI: PCI interrupt 0000:01:07.0[A] -> GSI 11 (level, low) -> IRQ 11 > > > bttv0: Bt878 (rev 17) at 0000:01:07.0, irq: 11, latency: 64, mmio: > > > 0xeb800000 > > > bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012 > > > bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected] > > > bttv0: gpio: en=00000000, out=00000000 in=00fff3ff [init] > > > tda9885/6/7: chip found @ 0x96 > > > bttv0: i2c: checking for MSP34xx @ 0x80... not found > > > bttv0: pinnacle/mt: id=4 info="PAL+SECAM / mono" radio=no > > > bttv0: using tuner=33 > > > bttv0: i2c: checking for MSP34xx @ 0x80... not found > > > bttv0: i2c: checking for TDA9875 @ 0xb0... not found > > > bttv0: i2c: checking for TDA7432 @ 0x8a... not found > > > bttv0: registered device video0 > > > bttv0: registered device vbi0 > > > bttv0: PLL: 28636363 => 35468950 . ok > > > bttv0: timeout: drop=338 irq=6288/30866, risc=1c07c03c, bits: HSYNC > > > OFLOW FDSR > > > bttv0: reset, reinitialize > > > bttv0: PLL: 28636363 => 35468950 . ok > > > bttv0: timeout: drop=595 irq=28513/83359, risc=05d5303c, bits: HSYNC > > > OFLOW > > > bttv0: reset, reinitialize > > > bttv0: PLL: 28636363 => 35468950 . ok > > > bttv0: timeout: drop=856 irq=31193/91527, risc=05d5303c, bits: HSYNC > > > OFLOW FBUS FDSR > > > bttv0: reset, reinitialize > > > bttv0: PLL: 28636363 => 35468950 . ok > > > > > > someone have similar pbs with tv card ? > > > > > Le mardi 01 fÃvrier 2005 Ã 14:21 -0500, Travis Osterman a Ãcrit : > > If your card has a hardware encoder you might try > > $ cat /dev/video0 > /tmp/test.mpg > > [ctrl+C to stop] > > $ mplayer /tmp/test.mpg > > > > to determine whether it's a card issue or a tvtime issue. I use the > > ivtv driver with my pvr-250 card. Good luck. > > > > -- Travis > > > > > > My card doesn't seem to have a hardware encoder but my card works fine > under winxp (double boot). So it could be a tvtime problem but i tried a > lot of tv viewer with the same result. It could also be a driver pb. I > believe to have seen in this list other people who have pbs with bttv > driver and the last kernel but i can't find this thread. > Eric > In fact, if i put the tuner to the right channel in windows and just reboot to linux i can view the same channel under tvtime but i'm not able to change channel. It seems to do nothing on the tuner to change channel. This is the same under xawdecode and zapping. Eric -- Eric Tanguy | Nantes, France <eric.tanguy@xxxxxxxxxxxxxx> Key : A4B8368F | Key Server : subkeys.pgp.net Fedora Core release 3 (Heidelberg) sur athlon kernel 2.6.10-1.741_FC3
Attachment:
signature.asc
Description: Ceci est une partie de message =?ISO-8859-1?Q?num=E9riquement?= =?ISO-8859-1?Q?_sign=E9e?=
