IT8212

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Folks

Is anyone succedd to use ITE8212 Raid controler (on Gigabyte boards called
GigaRaid) on FC3? 
I have some problem with building modules but dmesg shows:
	Found Controller: IT8212 UDMA/ATA133 RAID Controller
	FindDevices: device 0 is IDE
	FindDevices: device 1 is IDE
	Channel[0] BM-DMA at 0xA400-0xA407
	Channel[1] BM-DMA at 0xA408-0xA40F
	scsi2 : ITE RAIDExpress133
	  Vendor: ITE       Model: IT8212F           Rev: 1.3
	  Type:   Direct-Access                      ANSI SCSI revision: 00
	SCSI device sdb: 488397166 512-byte hdwr sectors (250059 MB)
	sdb: asking for cache data failed
	sdb: assuming drive cache: write through
	 sdb: sdb1
	Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
	  Vendor: ITE       Model: IT8212F           Rev: 1.3
	  Type:   Direct-Access                      ANSI SCSI revision: 00
	SCSI device sdc: 488397166 512-byte hdwr sectors (250059 MB)
	sdc: asking for cache data failed
	sdc: assuming drive cache: write through
	 sdc:<4>atkbd.c: Unknown key pressed (translated set 2, code 0x0 on
isa0060/serio0).
	atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
	atkbd.c: Unknown key pressed (translated set 2, code 0x0 on
isa0060/serio0).
	atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
	 sdc1
	Attached scsi disk sdc at scsi2, channel 0, id 1, lun 0

[root@beowulf scsi]# mount /dev/sdb1 /mnt/
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
...
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
kjournald starting.  Commit interval 5 seconds
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.

Best regards
Mile Davidovic, B.Sc.
--
Mile.Davidovic@xxxxxxxxxxxxxxx
MicronasNIT LLC.
http://www.micronasnit.com
Fruskogorska 11a, 21000 Novi Sad, Serbia & Montenegro
Phone (1) : +381 (0)21 475 00 24 (ext. 111)
Phone (2) : +381 (0)21 475 00 28 (ext. 112)
Fax           : +381 (0)21 450 721
 


[Index of Archives]     [Current Fedora Users]     [Fedora Desktop]     [Fedora SELinux]     [Yosemite News]     [Yosemite Photos]     [KDE Users]     [Fedora Tools]     [Fedora Docs]

  Powered by Linux