On Friday 28 September 2007, you wrote:
> My Toshiba Satellite A40 (i386, P4 Mobile) hangs during boot after:
With 'hpet-force-enable-on-ich34' reverted the system boots OK again.
We're not yet done though. It now fails to resume from suspend and there's
also the BUG (see subject) during power off. Possibly these are related.
Attached a diff of dmesg between 2.6.23-6 and 2.6.23-8. Nothing spectacular
AFAICT, except that I activated netconsole.
The details of that BUG are at the end of the diff.
I have some idea where to start looking for this one. If I'm not mistaken,
it should be somewhere between these two changes:
# good: [01762341418efa818f28dc69426ca7cc582cdc8c] git-wireless
# good: [ecdd2a3cb73af8b4659a4cb150bdf2a3ac908791] i386-pit-remove-the-useless-ifdefs
Cheers,
FJP
--- 2.6.23-rc6-686.dmesg 2007-09-19 19:32:00.000000000 +0200
+++ strider2.log 2007-09-29 23:55:18.000000000 +0200
@@ -1,335 +1,360 @@
-Linux version 2.6.23-rc6 (root@faramir) (gcc version 4.2.1 (Debian 4.2.1-4)) #1 SMP Wed Sep 19 16:31:00 CEST 2007
+Linux version 2.6.23-rc8-mm2 (root@faramir) (gcc version 4.2.1 (Debian 4.2.1-4)) #1 SMP Sat Sep 29 23:22:39 CEST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ef40000 (usable)
BIOS-e820: 000000001ef40000 - 000000001ef50000 (ACPI data)
BIOS-e820: 000000001ef50000 - 000000001f000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000ffe80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
495MB LOWMEM available.
-Entering add_active_range(0, 0, 126784) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 126784
HighMem 126784 -> 126784
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 126784
-On node 0 totalpages: 126784
- DMA zone: 32 pages used for memmap
- DMA zone: 0 pages reserved
- DMA zone: 4064 pages, LIFO batch:0
- Normal zone: 958 pages used for memmap
- Normal zone: 121730 pages, LIFO batch:31
- HighMem zone: 0 pages used for memmap
- Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F0180, 0014 (r0 TOSHIB)
ACPI: RSDT 1EF40000, 0038 (r1 TOSHIB 750 970814 TASM 4010000)
ACPI: FACP 1EF40060, 0084 (r2 TOSHIB 750 20030101 TASM 4010000)
ACPI: DSDT 1EF40558, 4B72 (r1 TOSHIB A000C 20031216 MSFT 100000E)
ACPI: FACS 000EEE00, 0040
ACPI: SSDT 1EF402CA, 0082 (r1 TOSHIB A000C 20030917 MSFT 100000E)
ACPI: DBGP 1EF400E4, 0034 (r1 TOSHIB 750 970814 TASM 4010000)
ACPI: BOOT 1EF40038, 0028 (r1 TOSHIB 750 970814 TASM 4010000)
ACPI: APIC 1EF40118, 0062 (r1 TOSHIB 750 970814 TASM 4010000)
ACPI: PM-Timer IO Port: 0xd808
-ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
-ACPI: IRQ0 used by override.
-ACPI: IRQ2 used by override.
-ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1f000000:dfc00000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 00000000000ee000
swsusp: Registered nosave memory region: 00000000000ee000 - 00000000000ef000
swsusp: Registered nosave memory region: 00000000000ef000 - 0000000000100000
-Built 1 zonelists in Zone order. Total pages: 125794
-Kernel command line: root=/dev/hda3 ro vga=791
-mapped APIC to ffffb000 (fee00000)
-mapped IOAPIC to ffffa000 (fec00000)
+Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125794
+Kernel command line: root=/dev/hda3 resume=/dev/hda6 ro vga=791 [email protected]/,@10.19.66.12/
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
-Detected 2793.139 MHz processor.
+Detected 2793.094 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
-Memory: 493688k/507136k available (1710k kernel code, 12840k reserved, 654k data, 232k init, 0k highmem)
+Memory: 495884k/507136k available (1736k kernel code, 10700k reserved, 1096k data, 236k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xdf800000 - 0xff7fe000 ( 511 MB)
lowmem : 0xc0000000 - 0xdef40000 ( 495 MB)
- .init : 0xc0355000 - 0xc038f000 ( 232 kB)
- .data : 0xc02abb3c - 0xc034f6dc ( 654 kB)
- .text : 0xc0100000 - 0xc02abb3c (1710 kB)
+ .init : 0xc03cb000 - 0xc0406000 ( 236 kB)
+ .data : 0xc02b2169 - 0xc03c41f4 (1096 kB)
+ .text : 0xc0100000 - 0xc02b2169 (1736 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
-Calibrating delay using timer specific routine.. 5590.71 BogoMIPS (lpj=11181437)
-Security Framework v1.0.0 initialized
+Calibrating delay using timer specific routine.. 5591.18 BogoMIPS (lpj=11182376)
+Security Framework initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
-CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
-CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b080 00004400 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
ACPI: Core revision 20070126
CPU0: Intel Mobile Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
-Total of 1 processors activated (5590.71 BogoMIPS).
+Total of 1 processors activated (5591.18 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
+net_namespace: 60 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd2fe, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
-ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
-ACPI: (supports S0 S3)
+ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region d800-d87f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region eec0-eeff claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11)
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 4 of device 0000:00:1d.0
PCI: Cannot allocate resource region 4 of device 0000:00:1d.1
-NET: Registered protocol family 8
-NET: Registered protocol family 20
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xe0000-0xeffff could not be reserved
pnp: 00:00: iomem range 0xf0000-0xfffff could not be reserved
pnp: 00:00: iomem range 0x100000-0x1ef3ffff could not be reserved
PCI: Bus 2, cardbus bridge: 0000:01:0b.0
IO window: 0000c000-0000c0ff
IO window: 0000c400-0000c4ff
PREFETCH window: 28000000-2bffffff
MEM window: 30000000-33ffffff
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: cff00000-cfffffff
PREFETCH window: 28000000-2bffffff
-PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:01:0b.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 18 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
-Switched to high resolution mode on CPU 0
-Freeing initrd memory: 5478k freed
+Freeing initrd memory: 2846k freed
Simple Boot Flag at 0x7c set to 0x1
audit: initializing netlink socket (disabled)
-audit(1190222757.716:1): initialized
+audit(1191102452.492:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
-Boot video device is 0000:00:02.0
PCI: Firmware left 0000:01:08.0 e100 interrupts enabled, disabling
vesafb: framebuffer at 0xd8000000, mapped to 0xdf880000, using 3072k, total 16192k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
+Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
PCI: Enabling device 0000:00:1f.6 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
+e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
+e100: Copyright(c) 1999-2006 Intel Corporation
+ACPI: PCI Interrupt 0000:01:08.0[A] -> GSI 20 (level, low) -> IRQ 18
+e100: eth0: e100_probe: addr 0xcffff000, irq 18, MAC addr 00:08:0d:17:bf:f5
+netconsole: local port 6665
+netconsole: local IP 10.19.66.11
+netconsole: interface eth0
+netconsole: remote port 6666
+netconsole: remote IP 10.19.66.12
+netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
+netconsole: device eth0 not up yet, forcing it
+e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
+netconsole: carrier detect appears untrustworthy, waiting 4 seconds
+console [netcon0] enabled
+netconsole: network logging started
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
-Freeing unused kernel memory: 232k freed
+Freeing unused kernel memory: 236k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Transitioning device [FAN] to D3
ACPI: Transitioning device [FAN] to D3
ACPI: Fan [FAN] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
-ACPI: Thermal Zone [THRM] (71 C)
+ACPI: Thermal Zone [THRM] (53 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
-SCSI subsystem initialized
usbcore: registered new device driver usb
-libata version 2.21 loaded.
-e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
-e100: Copyright(c) 1999-2006 Intel Corporation
-ACPI: PCI Interrupt 0000:01:08.0[A] -> GSI 20 (level, low) -> IRQ 18
-e100: eth0: e100_probe: addr 0xcffff000, irq 18, MAC addr 00:08:0D:17:BF:F5
-Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
-ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 19
-PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 19, io base 0x000018c0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
+SCSI subsystem initialized
+usb usb1: new device found, idVendor=0000, idProduct=0000
+usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
+usb usb1: Product: UHCI Host Controller
+usb usb1: Manufacturer: Linux 2.6.23-rc8-mm2 uhci_hcd
+usb usb1: SerialNumber: 0000:00:1d.0
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20
-PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 20, io base 0x000018e0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
-Marking TSC unstable due to: possible TSC halt in C2.
-Time: acpi_pm clocksource has been installed.
+usb usb2: new device found, idVendor=0000, idProduct=0000
+usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
+usb usb2: Product: UHCI Host Controller
+usb usb2: Manufacturer: Linux 2.6.23-rc8-mm2 uhci_hcd
+usb usb2: SerialNumber: 0000:00:1d.1
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 21
-PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:1d.7: debug port 1
-PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 21, io mem 0x2c080000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
+Marking TSC unstable due to: possible TSC halt in C2.
+Time: acpi_pm clocksource has been installed.
+usb usb3: new device found, idVendor=0000, idProduct=0000
+usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
+usb usb3: Product: EHCI Host Controller
+usb usb3: Manufacturer: Linux 2.6.23-rc8-mm2 ehci_hcd
+usb usb3: SerialNumber: 0000:00:1d.7
+Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
+ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
ICH4: chipset revision 3
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:DMA, hdd:pio
-Probing IDE interface ide0...
hda: HTS541080G9AT00, ATA DISK drive
-hda: selected mode 0x45
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
-Probing IDE interface ide1...
-Clocksource tsc unstable (delta = -473964036 ns)
+Clocksource tsc unstable (delta = -215345309 ns)
hdc: TOSHIBA DVD-ROM SD-R6112, ATAPI CD/DVD-ROM drive
-hdc: selected mode 0x42
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 156301488 sectors (80026 MB) w/7539KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
- hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
+ hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [email protected]
+Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
-input: PC Speaker as /class/input/input1
Real Time Clock Driver v1.12ac
-iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
-iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0xd860)
-iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
-pnp: Device 00:09 activated.
-parport_pc 00:09: reported by Plug and Play ACPI
-pnp: Device 00:09 disabled.
-pci_hotplug: PCI Hot Plug PCI Core version: 0.5
+input: PC Speaker as /class/input/input1
Linux agpgart interface v0.102
-shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
-intel_rng: FWH not detected
+agpgart: suspend/resume problematic: resume with 3D/DRI active may lockup X.Org
+on some chipset/BIOS combos (see DEBUG_AGP_PM in intel-agp.c)
agpgart: Detected an Intel 855GM Chipset.
agpgart: Detected 16252K stolen memory.
agpgart: AGP aperture is 128M @ 0xd8000000
+pci_hotplug: PCI Hot Plug PCI Core version: 0.5
+shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
+pnp: Device 00:09 activated.
+parport_pc 00:09: reported by Plug and Play ACPI
+pnp: Device 00:09 disabled.
input: Power Button (FF) as /class/input/input2
+Uniform watchdog device driver v0.01 loaded
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input3
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
ACPI: AC Adapter [ADP1] (on-line)
+ACPI: Battery Slot [BAT1] (battery present)
input: Video Bus as /class/input/input5
+iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10 (17-Aug-2007)
ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no)
-ACPI: Battery Slot [BAT1] (battery present)
-input: PS/2 Mouse as /class/input/input6
-input: AlpsPS/2 ALPS GlidePoint as /class/input/input7
Yenta: CardBus bridge found at 0000:01:0b.0 [1179:0001]
Yenta: ISA IRQ mask 0x04b8, PCI irq 16
Socket status: 30000007
pcmcia: parent PCI bridge I/O window: 0xc000 - 0xcfff
cs: IO port probe 0xc000-0xcfff: clean.
pcmcia: parent PCI bridge Memory window: 0xcff00000 - 0xcfffffff
pcmcia: parent PCI bridge Memory window: 0x28000000 - 0x2bffffff
ACPI: PCI Interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 17
-PCI: Setting latency timer of device 0000:00:1f.6 to 64
PCI: Enabling device 0000:00:1f.5 (0000 -> 0003)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
-PCI: Setting latency timer of device 0000:00:1f.5 to 64
+input: PS/2 Mouse as /class/input/input6
+input: AlpsPS/2 ALPS GlidePoint as /class/input/input7
cs: IO port probe 0x100-0x3af: excluding 0x1e0-0x1e7
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
-intel8x0_measure_ac97_clock: measured 55275 usecs
+iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0xd860)
+iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
+intel_rng: FWH not detected
+intel8x0_measure_ac97_clock: measured 55282 usecs
intel8x0: clocking to 48000
+Adding 554200k swap on /dev/hda6. Priority:-1 extents:1 across:554200k
EXT3 FS on hda3, internal journal
toshiba_acpi: Toshiba Laptop ACPI Extras version 0.18
toshiba_acpi: HCI method: \_SB_.VALZ.GHCI
fuse init (API version 7.8)
-e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
-eth0: no IPv6 routers present
+------------[ cut here ]------------
+kernel BUG at mm/slab.c:591!
+invalid opcode: 0000 [#1] SMP
+last sysfs file: /devices/pci0000:00/0000:00:1e.0/0000:01:0b.0/resource
+Modules linked in: ipv6 fuse dm_snapshot eeprom lm90 i2c_i801 i2c_core speedstep_ich speedstep_lib toshiba_acpi joydev tsdev pcmcia firmware_class snd_intel8x0 snd_intel8x0m snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss yenta_socket snd_pcm rsrc_nonstatic pcmcia_core snd_timer iTCO_wdt video output snd battery psmouse ac watchdog_core watchdog_dev button parport_pc parport shpchp pci_hotplug soundcore snd_page_alloc intel_agp agpgart evdev serio_raw pcspkr rtc ext3 jbd mbcache dm_mirror dm_mod ide_cd cdrom ide_disk piix generic ide_core ata_generic libata scsi_mod ehci_hcd uhci_hcd usbcore thermal processor fan
+
+Pid: 3763, comm: rmmod Not tainted (2.6.23-rc8-mm2 #1)
+EIP: 0060:[<c016df71>] EFLAGS: 00010046 CPU: 0
+EIP is at kfree+0x5e/0x97
+EAX: 00000000 EBX: dfe704b8 ECX: c2340d84 EDX: c13fcd40
+ESI: 00000286 EDI: dfe6ac65 EBP: c7204000 ESP: c7205f14
+ DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
+Process rmmod (pid: 3763, ti=c7204000 task=c201eab0 task.ti=c7204000)
+last branch before last exception/interrupt
+ from c016df66 (kfree+0x53/0x97)
+ to c016df6b (kfree+0x58/0x97)
+Stack: dfe704b8 dfe6ac65 dfe704c8 c01d975c dfe7048c c01d9772 00000880 c01da45a
+ 00000000 00000880 dfe70488 00000000 dfe705c0 00000000 dfe69395 dfe6a5f2
+ dfe6aba0 c01465a0 65737566 00000000 00000000 c21e75c0 c0163e91 c18df200
+Call Trace:
+ [<c01d975c>] kobject_cleanup+0x31/0x47
+ [<c01da45a>] kref_put+0x76/0x84
+ [<dfe69395>] fuse_sysfs_cleanup+0xa/0x14 [fuse]
+ [<dfe6a5f2>] fuse_exit+0x19/0x24 [fuse]
+ [<c01465a0>] sys_delete_module+0x1c0/0x228
+ [<c0103ece>] sysenter_past_esp+0x6b/0xa1
+ [<ffffe410>] 0xffffe410
+ =======================
+Code: aa 43 c0 8b 02 25 00 40 02 00 3d 00 40 02 00 75 03 8b 52 0c 8b 02 25 00 40 02 00 3d 00 40 02 00 75 03 8b 52 0c 8b 02 84 c0 78 04 <0f> 0b eb fe 8b 4a 18 64 a1 08 00 40 c0 8b 1c 81 8b 03 3b 43 04
+EIP: [<c016df71>] kfree+0x5e/0x97 SS:ESP 0068:c7205f14
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
