There are two errors that can lead to recovery problems with raid10
when used in 'far' more (not the default).
Due to a '>' instead of '>=' the wrong block is located which would
result in garbage being written to some random location, quite
possible outside the range of the device, causing the newly
reconstructed device to fail.
The device size calculation had some rounding errors (it didn't round
when it should) and so recovery would go a few blocks too far which
would again cause a write to a random block address and probably
a device error.
The code for working with device sizes was fairly confused and spread
out, so this has been tided up a bit.
Signed-off-by: Neil Brown <[email protected]>
### Diffstat output
./drivers/md/raid10.c | 38 ++++++++++++++++++++------------------
1 file changed, 20 insertions(+), 18 deletions(-)
diff .prev/drivers/md/raid10.c ./drivers/md/raid10.c
--- .prev/drivers/md/raid10.c 2007-02-20 17:10:15.000000000 +1100
+++ ./drivers/md/raid10.c 2007-02-20 17:11:41.000000000 +1100
@@ -429,7 +429,7 @@ static sector_t raid10_find_virt(conf_t
if (dev < 0)
dev += conf->raid_disks;
} else {
- while (sector > conf->stride) {
+ while (sector >= conf->stride) {
sector -= conf->stride;
if (dev < conf->near_copies)
dev += conf->raid_disks - conf->near_copies;
@@ -1801,6 +1801,7 @@ static sector_t sync_request(mddev_t *md
for (k=0; k<conf->copies; k++)
if (r10_bio->devs[k].devnum == i)
break;
+ BUG_ON(k == conf->copies);
bio = r10_bio->devs[1].bio;
bio->bi_next = biolist;
biolist = bio;
@@ -2021,19 +2022,30 @@ static int run(mddev_t *mddev)
if (!conf->tmppage)
goto out_free_conf;
+ conf->mddev = mddev;
+ conf->raid_disks = mddev->raid_disks;
conf->near_copies = nc;
conf->far_copies = fc;
conf->copies = nc*fc;
conf->far_offset = fo;
conf->chunk_mask = (sector_t)(mddev->chunk_size>>9)-1;
conf->chunk_shift = ffz(~mddev->chunk_size) - 9;
+ size = mddev->size >> (conf->chunk_shift-1);
+ sector_div(size, fc);
+ size = size * conf->raid_disks;
+ sector_div(size, nc);
+ /* 'size' is now the number of chunks in the array */
+ /* calculate "used chunks per device" in 'stride' */
+ stride = size * conf->copies;
+ sector_div(stride, conf->raid_disks);
+ mddev->size = stride << (conf->chunk_shift-1);
+
if (fo)
- conf->stride = 1 << conf->chunk_shift;
- else {
- stride = mddev->size >> (conf->chunk_shift-1);
+ stride = 1;
+ else
sector_div(stride, fc);
- conf->stride = stride << conf->chunk_shift;
- }
+ conf->stride = stride << conf->chunk_shift;
+
conf->r10bio_pool = mempool_create(NR_RAID10_BIOS, r10bio_pool_alloc,
r10bio_pool_free, conf);
if (!conf->r10bio_pool) {
@@ -2063,8 +2075,6 @@ static int run(mddev_t *mddev)
disk->head_position = 0;
}
- conf->raid_disks = mddev->raid_disks;
- conf->mddev = mddev;
spin_lock_init(&conf->device_lock);
INIT_LIST_HEAD(&conf->retry_list);
@@ -2106,16 +2116,8 @@ static int run(mddev_t *mddev)
/*
* Ok, everything is just fine now
*/
- if (conf->far_offset) {
- size = mddev->size >> (conf->chunk_shift-1);
- size *= conf->raid_disks;
- size <<= conf->chunk_shift;
- sector_div(size, conf->far_copies);
- } else
- size = conf->stride * conf->raid_disks;
- sector_div(size, conf->near_copies);
- mddev->array_size = size/2;
- mddev->resync_max_sectors = size;
+ mddev->array_size = size << (conf->chunk_shift-1);
+ mddev->resync_max_sectors = size << conf->chunk_shift;
mddev->queue->unplug_fn = raid10_unplug;
mddev->queue->issue_flush_fn = raid10_issue_flush;
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
