On Thu, Apr 06, 2006 at 12:12:04AM +0200, Bernhard Rosenkraenzer wrote:
> Attempting to use a USB 2.0 CF card reader in 2.6.16 and 2.6.16-mm2 (known to
> work back in 2.4 days, unused since) results in this:
Can you enable CONFIG_USB_STORAGE_DEBUG and send the kernel log file to
the linux-usb-devel mailing list so the people there can help you out?
thanks,
greg k-h
<linux-usb-devel people, here's the original log>
> usb 1-6: new high speed USB device using ehci_hcd and address 2
> usb 1-6: new device found, idVendor=0dda, idProduct=2005
> usb 1-6: new device strings: Mfr=3, Product=4, SerialNumber=5
> usb 1-6: Product: Card Reader
> usb 1-6: Manufacturer: Hama
> usb 1-6: SerialNumber: 000000000013
> usb 1-6: configuration #1 chosen from 1 choice
> usbcore: registered new driver libusual
> Initializing USB Mass Storage driver...
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usb-storage: device found at 2
> usb-storage: waiting for device to settle before scanning
> Vendor: Hama Model: CF Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:0: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:0: rejecting I/O to offline device
> sd 0:0:0:0: rejecting I/O to offline device
> sd 0:0:0:0: rejecting I/O to offline device
> sda : READ CAPACITY failed.
> sda : status=0, message=00, host=1, driver=00
> sda : sense not available.
> sd 0:0:0:0: rejecting I/O to offline device
> sda: Write Protect is off
> sda: Mode Sense: 00 00 00 00
> sda: assuming drive cache: write through
> sd 0:0:0:0: Attached scsi removable disk sda
> Vendor: Hama Model: SM Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:1: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:1: rejecting I/O to offline device
> sd 0:0:0:1: rejecting I/O to offline device
> sd 0:0:0:1: rejecting I/O to offline device
> sdb : READ CAPACITY failed.
> sdb : status=0, message=00, host=1, driver=00
> sdb : sense not available.
> sd 0:0:0:1: rejecting I/O to offline device
> sdb: Write Protect is off
> sdb: Mode Sense: 00 00 00 00
> sdb: assuming drive cache: write through
> sd 0:0:0:1: Attached scsi removable disk sdb
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> Vendor: Hama Model: SD Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:2: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:2: rejecting I/O to offline device
> sd 0:0:0:2: rejecting I/O to offline device
> sd 0:0:0:2: rejecting I/O to offline device
> sdc : READ CAPACITY failed.
> sdc : status=0, message=00, host=1, driver=00
> sdc : sense not available.
> sd 0:0:0:2: rejecting I/O to offline device
> sdc: Write Protect is off
> sdc: Mode Sense: 00 00 00 00
> sdc: assuming drive cache: write through
> sd 0:0:0:2: Attached scsi removable disk sdc
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> Vendor: Hama Model: MS Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:3: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:3: rejecting I/O to offline device
> sd 0:0:0:3: rejecting I/O to offline device
> sd 0:0:0:3: rejecting I/O to offline device
> sdd : READ CAPACITY failed.
> sdd : status=0, message=00, host=1, driver=00
> sdd : sense not available.
> sd 0:0:0:3: rejecting I/O to offline device
> sdd: Write Protect is off
> sdd: Mode Sense: 00 00 00 00
> sdd: assuming drive cache: write through
> sd 0:0:0:3: Attached scsi removable disk sdd
> usb-storage: device scan complete
>
>
> Any attempt to access the devices afterwards results in ENXIO (but
> the /sys/block entries for sda to sdd remain there).
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
