Hey Ben!
2.6.16 and 2.6.15-something show a funny behaviour
when using the radeonfb driver (for text mode), they
kind of twist and break the fonts in various places
some characters or parts seem to be mirrored like
'[' becoming ']' but not on character boundary but
more on N pixels, colors seem to be correct for the
characters, and sometimes the font is perfectly fine
for larger runs, e.g. I can read the logon prompt
fine, but everything I type is garbled ...
just for an example, when I type 'echo "Test"' then
all characters are mirrored and cut off on the right
side but the locations are as shown above, on enter
the T is only a few pixels wide, but the est part is
written perfectly fine ... this is a new behaviour
and going back to 2.6.13.3 doesn't show this ...
if there is some testing I can do for you, or when
you need more info, please let me know. here a few
details for the machine:
TIA,
Herbert
processor : 0
cpu : 7450, altivec supported
clock : 667.000000MHz
revision : 0.1 (pvr 8000 0201)
bogomips : 66.56
timebase : 33290001
machine : PowerBook3,3
motherboard : PowerBook3,3 MacRISC2 MacRISC Power Macintosh
detected as : 72 (PowerBook Titanium II)
pmac flags : 0000001b
L2 cache : 256K unified
pmac-generation: NewWorld
00:10.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Radeon Mobility M6 LY
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 255 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 48
Region 0: Memory at b8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at f0000400 [size=256]
Region 2: Memory at b0000000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at f1000000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
PCI: Enabling device 0000:00:10.0 (0086 -> 0087)
radeonfb (0000:00:10.0): Invalid ROM signature 8080 should be 0xaa55
radeonfb: Retrieved PLL infos from Open Firmware
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=166.00 Mhz, System=166.00 MHz
radeonfb: PLL min 12000 max 35000
radeonfb: Monitor 1 type LCD found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
radeonfb: Using Firmware dividers 0x0001003a from PPLL 0
radeonfb: Dynamic Clock Power Management enabled
Console: switching to colour frame buffer device 164x54
Registered "ati" backlight controller,level: 15/15
radeonfb (0000:00:10.0): ATI Radeon LY
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
